Hi, Looking for HP Data Protector Automation steps for Backup & Restoration for following DBs
1. Cassandra
2. MariaDB
3. Oracle
4. Some log servers.
Maximum OS stack would be Ubuntu and Container based solution. Anything related this would be of great help.
Hi
See Oracle support page for:
Bug 7519784 : ORA-600 [RBBPC_MEDIA_TOO_LONG] PROVIDING LIST OF MEDIA NAMES WITH SBTINFO2
Br,
Alesc
My clinet is getting restrted each time I start its backup.
I see below error on clinet:
Nov 9 01:00:10 dlpdcdbslp09 xinetd[15377]: START: omni pid=15033 from=::ffff:10.152.43.59
Nov 9 01:00:10 dlpdcdbslp09 xinetd[15377]: START: omni pid=15048 from=::ffff:10.152.43.59
Nov 9 01:00:10 dlpdcdbslp09 xinetd[15377]: START: omni pid=15075 from=::ffff:10.152.43.59
Nov 9 01:00:18 dlpdcdbslp09 kernel: program bma is using a deprecated SCSI ioctl, please convert it to SG_IO
Nov 9 01:00:33 dlpdcdbslp09 last message repeated 10 times
Nov 9 01:00:33 dlpdcdbslp09 xinetd[15377]: START: omni pid=18509 from=::ffff:10.152.43.59
Nov 9 01:00:36 dlpdcdbslp09 kernel: program bma is using a deprecated SCSI ioctl, please convert it to SG_IO
Nov 9 01:00:44 dlpdcdbslp09 last message repeated 9 times
Nov 9 01:00:45 dlpdcdbslp09 xinetd[15377]: START: omni pid=19735 from=::ffff:10.152.43.59
Nov 9 01:00:45 dlpdcdbslp09 xinetd[15377]: START: omni pid=19786 from=::ffff:10.152.43.59
Nov 9 04:03:12 dlpdcdbslp09 rhsmd: This system is registered to RHN Classic.
Nov 9 07:50:24 dlpdcdbslp09 kernel: st5: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).
Nov 9 07:50:24 dlpdcdbslp09 kernel: program bma is using a deprecated SCSI ioctl, please convert it to SG_IO
Nov 9 07:50:24 dlpdcdbslp09 xinetd[15377]: EXIT: omni status=4 pid=18509 duration=24591(sec)
Nov 9 07:52:34 dlpdcdbslp09 kernel: lpfc 0000:8b:00.1: 7:(0):0713 SCSI layer issued Device Reset (0, 0) return x2002
Nov 9 07:53:44 dlpdcdbslp09 kernel: lpfc 0000:8b:00.1: 7:(0):0714 SCSI layer issued Bus Reset Data: x2002
hi, everyone.
someone woould know to say me, if i for to upgrade the version 7 to 9 i neeed to buy the license for upgrade and for all features too?
You will need new licenses but if you have a current support contract there should be no charge.
HTH
Jeremy
Hi,
Thanks for the reply.
>omnidbutil -version
HP Data Protector A.07.00: OMNIDBUTIL, internal build 107, built on 31. maaliskuuta 2015, 11:08
I am trying to run the "omnidbutil -set_idb_password" command and descriebed in the links in my original post. It is not listed when I run the "-help" option and directly writing it just brings back the "-help" output (wrong syntax).
Thanks again!
Thanks for the reply Jeremy. It is a bit weird that on the official website there is this "NOTICE: The information in this Security Bulletin should be acted upon as soon as possible." but they recommend to the customers to not do it. I will try to contact HP support directly before I move on with patching other environments.
What Operating System version is the problem DP Media Agent Client?
What DP version is the problem DP Media Agent Client?
What Operating System version is the problem DP Cell Manager?
What DP version is the problem DP Cell Manager?
I'd suggest making sure the DP Cell Manager and the client have the latest DP patches.
`omnicheck -patches` `omnicheck -patches -host dlpdcdbslp09`
Also OS patches.
Is the system dlpdcdbslp09 32 or 64 bit ?
After patching the installation server to 9.04 you have to delete and reimport it.
Otherwise you will not be able to "add" the mysql integration to a client.
Good... done... works fine ...
Problem :
"Be aware, for using the MySQL Backup you need the "new" ... "Advanced Online Integration License".
So ... how can I upgrade my "normal" Online Integration License" to the Advanced one ???
This is what i get :
[Normal] From: BSM@aii-dp "pfo-obsdb01_MYSQL_online" Time: 09.11.2015 16:08:33
Backup session 2015/11/09-5236 started.
[Warning] From: BSM@aii-dp "pfo-obsdb01_MYSQL_online" Time: 09.11.2015 16:08:33
License not available "Extended On-line Backup for Win/Lin Software"
[Normal] From: BSM@aii-dp "pfo-obsdb01_MYSQL_online" Time: 09.11.2015 16:08:33
You'll have to buy a license.
You might be able to find a 30-day evaluation license so that you can check it's really what you want first.
HTH
Jeremy
Hi All,
My Issue is as below, any advice is greatly appreciated:
There are a number of slots in a single VTL that I created that are now showing as 'poor' and as 'unknown' for their format in DP 9.04, some are even showing as just a grey slot symbol with their number (not identifier) and without a blue question mark. Backups had been running fine for weeks untilt his issue began a couple of days ago.
Error messages are:
cannot write filemark
cannot rewind medium
cannot close device
cannot unload exchanger medium
The backup jobs hang at ‘loading medium from slot’, then eventually the next message I get is ‘Ejecting medium’, then ‘aborting media agent ‘servername_vtl_drive[numer]’
DP then tries to use another drive for the backup but encounters the same issue, occasionally it gives the ‘cannot rewind medium’ error after dismounting a drive it has been unable to use. It then marks the slots that it has been unable to use as ‘Quality: Poor’ as a result. They had previously been showing as ‘Quality: Good’ before the backup jobs tried to use them.
I have looked at the VTL and the HP B6200 Storeonce device that is hosting it, isn’t reporting anything out of the ordinary. I am unable to scan both media showing as ‘poor’ and also media showing as ‘unknown’. I am also unable to format that media too, it hangs at ‘loading medium from slot’ the same as the backup jobs do.
I have been able to use the ‘omnimm –reset_poor_medium’ command to change the ‘poor’ drives back to ‘good’ but this doesn’t seem to be much use.
I was wondering if anyone had encountered this before? or might know what could be causing it?
Many Thanks
In my configuration I have the following setup
Main Site:
CM on windows server 2008 R2
StoreOnce Software Store on Linux
DR Site:
StoreOnce Software Store on Linux
I wanted to list my StoreOnce stores from the Cell Manager. Primarily to test if the Store was running. We are on 9.04 and previously we were having difficulty with the Store at the DR Site stopping. We think this was due to bad connections during syncs with the Main site.
The fix in most of those cases has been to reboot one or both of the StoreOnce Software Stores.
When I try doing the following commands from a command prompt on the CM:
cd "C:\Program Files\OmniBack\bin\"
storeonceinfo.exe -list_stores -type=SOS -host <dpStorehostname>
I get the following error:
"C:\Program Files\OmniBack\bin\storonceinfo.exe is not a valid Win32 application."
The first three times I ran it the program worked on Windows 2008 R2, but now it does not.
Why?
Clinet in Red hat linux host
DP is 7.0
CM is Windows 2008 R2
Clinet has below patches:
DPUX_00084/DPLNX_00372 Core Component
DPUX_00086/DPLNX_00374 Disk Agent
DPUX_00087/DPLNX_00375 Media Agent
PHSS_43671/DPLNX_00258(BDL703) Automatic Disaster Recovery Module
Hello!
I have a question. We have 4 Media Server. 2 for the Tape Libraries and 2 for vmware.
Is it possible to identify these Server with registrykey or similar?
rg.
Hansi
Hi,
the problem might be caused by a SCSI problem with the devices/changer. You need to check your fibre channel settings for the VTL used and presented to the host. Check if zoning is correct and server is connected. Use LTT Tools to try connecting to the VTL. Use "uma -ioctl <SCSI address of changer> -barcode" to see if you can connect to the VTL. Use "devbra -dev" to check if the devices are displayed as expected. In DP GUI, check if SCSI address for the changer and devices have changed.
Best regards
Daniel
Hi,
you could use the command "omnirsh <client> INFO" to get information from the client which components are installed.
Best regards
Daniel
I got the same problem；my client host‘s “noaccese” user forbidden by system adm。 after reuse the user，I remote installe successed。
Hello!
thank you for answer.
But I need a Identifiacation for example in registry.
I have found a key HKEY_LOCAL_MACHINES\SOFTWARE\Hewlett-Packard\Openview\OmniBackII\Features\
This could be the path I need for authentificate the feature of a server:
is this correct?
rg
hansi
Hi,
Here is my situation
I currently have reports that have sent method "LOG" and the lors are saved on our network.
Some of those reports have, in their name (Log to file / path) the variable %date.
For exemple, we are saving daily "list of all session in the last 24 hours report" once a day.
\\SERVER\SHARE\Daily_ListAllSessions_%date.html create report with names like : Daily_ListAllSessions_11092015.html.
We have those reports configured for a long time and we can't remember where we found that %date in the log name would work. I searched in every corner of forums and documentations we have and there is no mention of it.
It is probably not a Windows variable so our guess is it is a DP variable.
What I tried and know is :
My problem is :
We now want to produce report for every job running by creating a notification event that create the report after job ends.
Having %date in the name is bad because reports don't have a unique name and Session Object Report are overwritten over and over during the day.
We could use only %time but we feel that we may loose some reports if 2 jobs end at the same time.
As I said, using %date and %time together will only "translate" the first variable of the name
My question :
Do you guys know about those variables ?
Do you know a way we could put more than one variable in our Log save path in order to have a unique name for each report created ?
Do you know other variables that would help create a unique name (like SESSION ID or something) ?
Thank you for any help you could give me.
Have a good day.
Alainboots